• Bush Hog Fth 720 Manual
• Bush Hog Fth 600 For Sale
• Bush Hog Fth 600 User Manual Download
• Bush Hog Fth 600 Blades

SECTION IV

View and Download Bush Hog FTH 480 instruction manual online. Bush Hog: Bush Hog FTH 600 Rotary Cutter Parts Diagrams. FTH 600 ROTARY CUTTER CATALOG SEARCH. Note: Use keywords or part numbers instead of full sentences for best results. Examples: 737-3025, 1234, filter, oil, pump, etc. Parts Catalog Sections. FREQUENTLY ASKED QUESTIONS.

1-1 INTRODUCTION. We are pleased to have you as a Bush Hog cus-tomer.Your ATH/FTH Series Rotary Cutter has been carefully designed to give maximum service with minimum down time.This manual is provided to give you the necessary operating and maintenance instructions for keeping your rotary cutter in top operating condition. View and Download Bush Hog Tough FTH-600 specifications online. Flat Deck Side Discharge Finishing Mowers. Tough FTH-600 Lawn and Garden Equipment pdf manual download. Bush hog® Tough FeaTures Tough Fabricated 7 gauge Decks Tough Cat 3 Drivelines Tough Commercial grade greaseable spindles Tough 5 Year gearbox Limited Warranty Tough Kevlar reinforced Belt Tough Powder Coat Paint SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Page 3 Model FTh-720 MoDeLs FTh-600 FTh-720 Cutting Width 60 inches 72 inches. Browse all pages of the user manual Bush Hog Tough ATH-600, translate them to other languages. In every user manual you will usually find a schematic diagram of Bush Hog Tough ATH-600 as well as tips for servicing Bush Hog Tough ATH-600. You will also learn how to configure the device Bush Hog Tough ATH-600 to suit your requirements. Bush Hog Lawn Mower FTH 600. Bush Hog Lawn Mower User Manual. See Prices; Bush Hog Lawn Mower FTH-600. Bush Hog Flat Deck side Discharge Finishing Mowers Specification Sheet. See Prices; Bush Hog Lawn Mower FTH-720. Bush Hog Flat Deck side Discharge Finishing Mowers Specification Sheet.

MAINTENANCE

4-1 MAINTENANCE CHECK LIST

Perform scheduled maintenance as outlined below.
Lower implement to ground, turn off tractor, and set
parking brake before doing maintenance inspections
or work. Some checks may require raising machine
off ground and supporting with blocks. All bolts
should be torqued as indicated in torque chart
unless otherwise indicated.

THE CUTTER CAN FALL FROM
HYDRAULIC SYSTEM FAILURE. TO
AVOID SERIOUS INJURY OR DEATH,
SECURELY SUPPORT CUTTER BEFORE
WORKING UNDERNEATH.

BEFORE EACH USE.

1. Check tractor tire air pressure. Refer to tractor

operator’s manual. Check mower tire pressure (if
pneumatic tires). Tire pressure should be 30 psi.

2. Check blades and spindles to be sure that

no foreign objects such as wire or steel strapping
bands are wrapped around them.

3. Check blade bolts for tightness. Tighten

blade bolts to 76 ft./lbs.

4. Inspect blades for wear. Replace if necessary

per paragraph 4-5. Use only genuine Bush Hog
replacement parts. If it is necessary to sharpen the
blades, remove the blades from the spindles before
sharpening. DO NOT sharpen blades while still
attached to mower.

5. Make certain all shields are in place and in

good condition. Repair or replace any missing or
damaged shields.

6. Inspect wheel(s) for wear, damage or foreign

objects. Repair or replace if necessary.

7. Perform BEFORE EACH USE lubrication per

paragraph 4-2.

8.During operation, listen for abnormal sounds

Precautions1. ContentsMiscellaneous Connections. Integra dtr 50.1 user manual diagram. ModelsRecording of copyrighted material for other than personal use is Note to CATV. Recording Copyright For U.S.

which might indicate loose parts, damaged bearings,
or other damage. Correct any deficiency before con-
tinuing operation.

AFTER EACH USE

1. Clean all debris from machine especially under-

side of deck, underneath belt shield and off safety
decals. Replace any missing or illegible decals.

2. Inspect cutter for worn or damaged compo-

nents. Repair or replace before next use. Any
replacement components installed during repair shall
include the components’ current safety decals speci-
fied by the manufacturer to be affixed to the compo-
nent.

3. Store cutter in a dry place.

40 HOURS

1. Check belt for proper tension. Refer to para-

graph 4-3.

4-2 LUBRICATION

(Figures 4-1A, & B)

BEFORE EACH USE

1. Driveline Universal Joints - Apply multi-purpose

grease with grease gun.

2. Driveline Guard - Apply 2-3 shots of multi-pur-

pose grease with grease gun to plastic fitting.

Bush Hog Fth 720 Manual

3. Wheels - Apply multi-purpose grease wiith

grease gun.

4. Caster Pivot - Apply multi-purpose grease with

grease gun.

40 HOURS

5. Input Gearbox - Add EP80W-90 gear oil, if nec-

essary, to bring oil level to check plug.

20 HOURS

6. Driveline - Disconnect PTO driveline, pull the

two sections apart, thoroughly clean old grease from
tubes and apply thin coat of multi-purpose grease to
outside of inner (male) section. Reassemble sec-
tions and install. Pull each section to be sure drive-
line and shields are securely connected. Make cer-
tain PTO shielding is in good condition.

NOTE

The multi-purpose grease referenced in this

secftion is an NLGI Grade 2 type grease.

Figure 4-1B

(6) 20 Hours

(2) Before Each Use

(1) Before Each Use

10

(4) Before Each Use

Figure 4-1A

(5) Before Each Use

(3) Before Each Use

WARNING

Bush Hog® TOUGH

Flat Deck Side Discharge

Finishing Mowers

Bush Hog® TOUGH Features

TOUGH Fabricated 7 Gauge Decks

TOUGH Cat 3 Drivelines

TOUGH Commercial Grade

Greaseable Spindles

TOUGH 5 Year Gearbox Limited Warranty

Bush Hog Fth 600 For Sale

TOUGH Kevlar Reinforced Belt Model FTH-720

TOUGH Powder Coat Paint

Bush Hog Fth 600 User Manual Download

Bush Hog Fth 600 Blades